3629 Cutter (Guillotine)

Specifications

Equipment

Modes of Operation: The cutter may be used as a stand-alone device, or in combination with other Pitney Bowes equipment.

 

Accessories and Attachments:

Simple Conveyor for 3629 (Model 3636)

Tabletop (non-intelligent) interface (Model 3637)

Stacker Tray for 3629 for stand alone operation (Model 3638)

Decollator Kit for 3629 (Model 3639)

Centre Slitter for 3629 (Part No. 9296208) - cutter will accept up to four (Model 3640)

Collating Conveyor (Model 3642)

3 Bin Outsort Kit (Model 3643)

OMR Module (Model 3641)

Automatic Drop Stacker (Part No.SV.83156)

Conveyor Stacker (Part No. SV.83466)

 

Electrical: 3629: 90-250VAC, 50/60Hz, 3A, 3642: 90-250VAC, 50/60Hz, 2A

 

Stand-Alone Dimensions: 1090mm High x 790mm Wide x 410mm Long overall (length increases to approximately 1m with stacker or conveyor fitted)

Paper path height is adjustable from 950mm to 1020mm to accommodate the requirements of different Pitney Bowes mailing systems.

 

Weight: 3629 -112 kg, 3636 - 13kg, 3642 - 21kg

 

Speed: Variable. Top speed is programmable for each job. Maximum hourly rate in stand-alone mode assuming standard 80gsm bond, double cut, continuous cycle:

A4 paper (12" length) 9,000 per hour

100mm (4") length paper 14,000 per hour

 

Noise Level: 75 dB(A)

 

 

Material

3629 Stand-Alone

Paper Weight: 40gsm to 150gsm * [* 400gsm maximum for multipart forms]

Length: 76mm to 610mm

Maximum Width: (including sprockets) is 415mm plus an edge trim margin of up to 25mm on each side.

Minimum width: (including sprockets) is 127mm plus an edge trim margin of up to 25mm on each side.

 

3629 On-Line

Paper Weight: 60gsm to 150gsm

Length: 102mm to 356mm

Width: Maximum width on conveyor is 241mm

Minimum width on conveyor is 152mm

Outsort Bin Capacity: 120 sheets of 80gsm bond in each bin

 

 

SCAN DASH MARK POSITIONING FOR STANDARD SCANNER

Refer to Figure below.

A scan dash line must be a minimum of 6mm (0.25”) width. A solid black line is preferred, but if the mark is printed using hyphens, it must be at least two hyphens wide with no more than 0.8mm separation between the hyphens. The marks should be black ink on a light background.

 

All scan lines must be printed within an area a minimum of 12mm from the lower edge of the form to a maximum of 114mm from the lower edge i.e. A scan dash zone of 102mm. The outer edge of the scan dash area is a minimum of 2 character widths in from the trimmed edge of the form.

 

There must also be a clearance of a minimum of 12mm from any text to the first mark and also above the last mark before any printed text on the form.

 

There must be at least 6mm spacing from any scan dash line to any other printed matter on the form.

 

Forms must be fed `foot first' through the cutter.

SCAN DASH POSITIONING WITH EXTENDED SCANNER KIT FITTED

(See Figure below)

A scan dash line must be a minimum of 6mm width. A solid black line is preferred, but if the mark is printed using hyphens, it must be at least two hyphens wide with no more then 0.8mm separation between the hyphens. The marks should be black ink on a light background.

 

All scan lines must be printed within an area a minimum of 12mm from the lower edge of the form to a maximum of 241mm from the lower edge i.e. A scan dash zone of 228mm. The outer edge of the scan dash area is a minimum of 2 character widths in from the trimmed edge of the form.

 

There must also be a clearance of a minimum of 12mm from any text to the first mark and also above the last mark before any printed text on the form.

 

There must be at least 6mm spacing from any scan dash line to any other printed matter on the form.

 

Forms must be fed `foot first' through the cutter.