DI350/DI380/DI400/DI425 and
Spectrum 3 Series
Inserting Machines

Specifications

IMPORTANT

The specifications below are subject to material test and are subject to change without notice. They are supplied for information purposes only and do not form any guarantee of machine performance by Pitney Bowes.

Equipment

Physical Dimensions:

DI350/DI400/3 series: 915mm long x 510mm deep x 610mm high

DI380: 773mm long x 568mm deep x 525mm high

DI425: 1043mm long x 568mm deep x 525mm high

Weight:

55kg (DI350/DI380/DI400/3 series)

65kg (DI425)

Noise Level (Running): 73dBA

Electrical: 230V, 50Hz, 3A

Speed:

DI350/3 Series: Up to a maximum of 2500 cycles per hour (depending on fold type and material quality)

DI380: Up to a maximum of 3000 cycles per hour (depending on fold type and material quality)

DI400/DI425: Up to a maximum of 3500 cycles per hour (depending on fold type and material quality)

Fold Modes:

Single fold
C - Letter fold
Z - Accordion fold
Double fold

Material

Sheet Feeders:

Minimum sheet size: 127mm Width x 127mm Length

Maximum sheet size: 229mm Width x 406mm Length

Paper weights: 60gsm Minimum (70gsm for OMR) to 120gsm Maximum

Fold configurations: Material length limits before folding

Single fold: 127mm - 315mm
C - Letter fold: 150mm - 356mm
Z - Accordion fold: 201mm - 356mm
Double fold: 305mm - 406mm

Double Document Detector Material range: 60gsm Minimum to 120gsm Maximum

Feed tray capacity:

DI350/DI400/3 series: Up to a maximum of 100 sheets of 80gsm

DI380/DI425: Up to a maximum of 325 sheets of 80gsm

Daily Mail (Hand feed) mode: Stapled sets up to 5 sheets of 80gsm to a maximum total weight of 400gsm per set can be processed in the Daily Mail mode. Only Sheet Feeder number 1 (plus the Insert Feeder if required), can be used for Daily Mail applications. The maximum compressed thickness after folding should not exceed 2mm. Glossy/coated sheets are not recommended.

Fold Type and Overall Thickness Limits:
The maximum number of sheets that can be accumulated or collated varies with fold type, and paper weight. Refer to the Operating Guide for full details.

Insert Feeder:

Minimum Insert size: 127mm Width x 82mm Length

Maximum Insert size: 230mm Width x 152mm Length

Minimum Paper Weight: 75gsm Minimum (non-folded cut sheet) 60gsm (folded material)

Maximum Paper Weight: 180gsm (Single Sheet), and Inserts of up to a maximum compressed thickness of 2mm.

Pre-folded or single panel Inserts should be fed from the Insert Feeder.

Double Document Detector Material range: 60gsm to 120gsm.

Feed tray capacity: Up to a maximum of 100 Inserts (300 on DI425 only)

Sealer: Maximum of 1200 envelopes between refills.

Stacker: Up to 150 filled envelopes. (Dependent on size and contents of the envelope).

Envelope Feeder

Envelope Depth: 88mm to 164mm

Envelope Width: 220mm to 242mm

Envelope weights: 65gsm to 100gsm

Envelope tray capacity: Up to a maximum of 100 envelopes (300 on DI425 only)

End Clearance: End clearance between the Insert and envelope is a minimum of 6mm at each side i.e. a minimum of 12mm overall. This measurement should be taken with all documents placed into the envelope.

Depth Clearance: The Insert must allow a minimum clearance of 3mm for unfolded documents, and 6mm for folded documents, below the flap crease after it is fully inserted into the envelope.

Envelope flap and throat requirements:

Flap Depth: 25mm to 63mm

Throat Depth: 6mm to 41mm, throat depth at 19mm in from edge of envelope must be between 1.6mm and 6mm.

Closed flap tip should not come closer than 44mm to bottom of envelope.

Material Requirements:

For best performance, use only materials approved by Pitney Bowes.

Materials should be good quality and properly stored.

Recommended storage conditions: 18°C to 25°C, 40% to 60% relative humidity

Compliance
 

Pitney Bowes certifies that the DI350/DI380/DI400/DI425 and SPECTRUM 3 Series™ comply with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC.