|
|
|
|
|
DA300 Envelope Printer Specifications
|
 |
Equipment Physical Dimensions: 370mm high x 410mm wide x 550mm deep (without wireform) Weight: 18.1kg including print cartridge and catch bin. Shipping weight: 25kg Electrical: 220-240VAC, 50Hz, 0.5A Interface: Centronics Parallel and serial port. Control Language: PCL5, modified Driver Compatibility: Windows 99/ME/2000/NT/XP compatible Address Recovery: Memory buffer holds a maximum of 20 addresses Print Modes (Print Resolution)
Resident Fonts
Resident Font Enhancements
Downloadable Fonts: Supports bitmapped, downloadable fonts. Cartridge Fonts: Not required. Fonts are downloaded with addresses. Barcode Printing: The DA300 can print a 5- or 11-digit USPS NAIC-certified POSTNET barcode in one of three positions: the lower right of the envelope; above the address block; and below the address block. Throughput: 750 to 4400 pieces per hour, depending on print mode, media size, number of address lines, and barcode imprinting. Input Stacker Capacity: 200 DL size Envelopes Output Stacker Capacity: 150 DL size Envelopes Effective Print Area: The printable width is 238mm measured from the right side of the mailpiece. The printable height is 343mm measured from the bottom edge of the mailpiece. Ink Cartridge: User-replaceable ink jet Print Position Accuracy for a DL size envelope :
Print Position Accuracy for other media:
Operating Temperature: 13 to 35ºC Operating Humidity: 8 to 80% Storage Temperature (Printer): -9 to 49ºC Storage Humidity (Supplies): 5 to 95% Shipment Temperature (Printer): -20 to 60ºC Shipment Humidity (Supplies): 5 to 100% Noise Level: Idle <6.6 Bel (A), Operating <7.3 Bel(A), Operator position: no more than 65 dBa referenced to 20 µpa Recommended Usage: Pitney Bowes has tested this machine under many different conditions and recommends that you do not exceed the usage levels specified below:
NOTE: Usage beyond these recommended cycles is not covered under the Pitney Bowes Equipment Maintenance Agreement.
Material Approved Media: The paper types listed below are approved for use with the DA300 Printer. Please note that the dimensional limits above apply in all cases, and that all media (flats, envelopes, postcards, catalog envelopes, etc.) must be without windows, unstuffed and unsealed.
Material Size: 127mm to 324mm wide x 76mm to 343mm high Material Thickness: 0.08mm to 1.6mm Material Notes: Envelopes have a flap along the long edge and are processed by the printer non-flap edge first. Envelopes may have either a diagonal or straight edge along the envelope flap. Booklets are defined as media having physical dimensions 150 x 230mm or larger. Booklets have an opening along their long edge which is covered by a flap with an adhesive seal. Catalog envelopes have an opening along their short edge which is closed by a flap with an adhesive seal. Postcards have no folds or bends. The printable side may have a higher surface roughness than the non-printable side. Self-mailers may be of "C," "Z," or 1/2-folded construction. They may not exceed the maximum allowable thickness as specified on the previous page and must be tabbed per postal regulations. A catalog may consist of multiple pages bound by adhesive or tabs on the feed edge or at 90 degrees with respect to the feed edge. Sheet stock may consist of 60 to 105gsm bond as well as 225 to 300gsm coated stock. The size and thickness constraints specified above apply.
Pitney Bowes certifies that the DA300 complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC. |
||
 |
||||
