|
IMPORTANT
|
The specifications below are subject to material test and are subject to change without notice. They are supplied for information purposes only and do not form any guarantee of machine performance by Pitney Bowes.
|
Equipment
Physical Dimensions: 1370mm long x 570mm deep x 760mm high
Weight: 88kg to 102kg (depends on configuration)
Noise Level: 72dBA to 74dBA
Electrical: 100VAC to 240VAC, 50/60Hz, 10A
Speed:
DI500 Series: Up to a maximum of 3600 cycles per hour (depending on fold type and material quality)
DI600: Up to a maximum of 4000 cycles per hour (depending on fold type and material quality)
Fold Modes:
- Single fold
- “C” - Letter fold
- “Z” - Accordion fold
- Double fold
Material
Sheet Feeders A, B, C and D:
- Minimum sheet size:
- 127mm Width x 175mm Length (non OMR)
- 203mm Width x 175mm Length (with OMR)
Maximum sheet size: 229mm Width x 406mm Length
- Paper weights:
- 60gsm Minimum to 120gsm Maximum (non OMR)
- 75gsm Minimum to 120gsm Maximum (with OMR)
Fold configurations: Sheet length limits before folding
- Single fold: 175mm - 305mm
- “C” - Letter fold: 242mm - 347mm
- “Z” - Accordion fold: 242mm - 347mm
- Double fold: 319mm - 406mm
Double Document Detector Material range: 60gsm Minimum to 120gsm Maximum
Feed tray capacity: Up to a maximum of 325 sheets of 80gsm
Manual Feed mode: Stapled or unstapled sets up to 5 sheets of 80gsm to a maximum total weight of 400gsm per set can be processed in the Manual Feed mode. The maximum compressed thickness after folding should not exceed 3mm. Glossy/coated sheets are not recommended.
Insert Feeders F and G:
Minimum Insert size: 127mm Width x 82mm Length
Maximum Insert size: 230mm Width x 152mm Length
Minimum Paper Weight: 75gsm Minimum (non-folded cut sheet) 60gsm (folded material)
Maximum Paper Weight: 180gsm (Single Sheet)
Max compressed thickness of insert: 2mm for feeder F, 1.5mm for feeder G
Double Document Detector Material range: 60gsm to 120gsm.
Feed tray capacity: Up to a maximum of 300 Inserts
- Fold Type and Overall Thickness Limits:
- The maximum number of sheets that can be accumulated or collated varies with fold type, a paper weight. Refer to the Operating Guide for full details.
- The total Mail Piece contents must not exceed 3mm total compressed thickness.
Sealer: Maximum of 3,000 envelopes between refills.
Drop Stacker: Up to 150 filled envelopes. (Dependent on size and contents of the envelope).
Envelope Feeder:
Envelope Depth: 98mm to 164mm
Envelope Width: 164mm to 242mm
- Envelope depths for SwiftStart and Manual Feed:
- 109mm, 111mm, 114mm, 121mm, 162mm
Envelope weights: 65gsm to 100gsm
Envelope tray capacity: Up to a maximum of 300, 90gsm envelopes
End Clearance: End clearance between the Insert and envelope is a minimum of 6mm at each side i.e. a minimum of 12mm overall. This measurement should be taken with all documents placed into the envelope.
Depth Clearance: The Insert must allow a minimum clearance of 3mm for unfolded documents, and 6mm for folded documents, below the flap crease after being fully inserted into the envelope.
Envelope flap and throat requirements:
Flap Depth: 25.5mm to 63mm
Throat Depth: 6mm to 41mm, throat depth at 19mm in from edge of envelope must be between 1.6mm and 6mm.
Closed flap tip should not come closer than 44mm to bottom of envelope.
Material Requirements:
For best performance, use only materials approved by Pitney Bowes.
Materials should be good quality and properly stored.
Recommended storage conditions: 18°C to 25°C, 40% to 60% relative humidity
- Compliance
-
Pitney Bowes certifies that the DI500/DI600 Series comply with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC. The products were tested in a typical configuration.
WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
|
